Minimal Hardware/Software Setup
Hi folks. Just joined. I want to contribute.
Can anybody suggest the best setup with the equipment I have?
- iPhone 4
- iPhone 6
- MacBook Air
- Garmin GPSMap62
- Raspberry Pi 2's (2 versions) kicking around
I'm also a developer. I'd like to have a system where I can grab some recently sniffed data. I can match up timestamps if need be.
Thanks in advance. Cheers
Can anybody suggest the best setup with the equipment I have?
- iPhone 4
- iPhone 6
- MacBook Air
- Garmin GPSMap62
- Raspberry Pi 2's (2 versions) kicking around
I'm also a developer. I'd like to have a system where I can grab some recently sniffed data. I can match up timestamps if need be.
Thanks in advance. Cheers
I go with this very minimal setup: a rpi0, a Tp-Link TL-WN722N and a ublox-7 based mouse GPS, and a power bank, of course.
And for the software, I use a software I wrote: https://github.com/solsticedhiver/ssid-logger
And for the software, I use a software I wrote: https://github.com/solsticedhiver/ssid-logger
This is super-cool!
Do you have cool pictures to help inspire people?
Cheers and great work,
-Ark and the WiGLE team
Do you have cool pictures to help inspire people?
Cheers and great work,
-Ark and the WiGLE team
@arkasha this is a question for me ?
I previously posted about this in viewtopic.php?f=3&t=2751&sid=831d48cccb ... 48d#p10501
It looks like this https://imgur.com/a/9ne8HgW I changed the cord for some elastic. But not much of a change since.
I would have like to 3D print a case but that is a bit out of my league, and I don't have a 3D-printer at hand to avoid printing cost.
Edit:
I made a quick tutorial to describe the software/OS setup I used. It is not complete yet, but it gives an idea. https://github.com/solsticedhiver/ssid- ... hlinux-arm
I previously posted about this in viewtopic.php?f=3&t=2751&sid=831d48cccb ... 48d#p10501
It looks like this https://imgur.com/a/9ne8HgW I changed the cord for some elastic. But not much of a change since.
I would have like to 3D print a case but that is a bit out of my league, and I don't have a 3D-printer at hand to avoid printing cost.
Edit:
I made a quick tutorial to describe the software/OS setup I used. It is not complete yet, but it gives an idea. https://github.com/solsticedhiver/ssid- ... hlinux-arm
yeah - just prompting you to show off!
-a
-a
I tried one of the integrated "USB hats" with pogopins to see if i could decrease the footprint of my Pi stumbling rig, but it increased the power consumption vs. a simple Anker OTG hub. I also have some single- micro->A "inserts" that turn the OTG micro USB into a single A 'tab' that slides into a male A connector (super weird!) if you can bear to stumble with the internal radio and just need GPS.
OK. That's interesting for the USB hats. I will not try that then. Do you have any rough figure about the increase consumption power ?
I don't visualize what could be your micro to A USB insert. Is it something like what I used ? I have a micro to A 90° right angle adapter, you can see that on the photo.
I have not tried to use the wifi card of the rpi0 to sniff wifi beacon. You have to use a special driver and even modify the firmware ? I found that not easy the last time I tried.
I don't visualize what could be your micro to A USB insert. Is it something like what I used ? I have a micro to A 90° right angle adapter, you can see that on the photo.
I have not tried to use the wifi card of the rpi0 to sniff wifi beacon. You have to use a special driver and even modify the firmware ? I found that not easy the last time I tried.
No figures on the power consumption, just that I was seeing rail decoupling.
This little beast is the adapter I use:
https://www.adafruit.com/product/2910
This little beast is the adapter I use:
https://www.adafruit.com/product/2910
I haven't looked into the driver/build for the pwnagotchi, but they clearly have full access to the radio, for what they do.
https://pwnagotchi.ai/
https://pwnagotchi.ai/
I was thinking of the nexmon driver: https://github.com/seemoo-lab/nexmon
That's what I tried. That's what the pwnagotchi project must use.
By the way, I forgot that I use a rpi0 with no (built-in) wifi, so this is not relevant for me![Wink ;-)](./images/smilies/icon_wink.gif)
Edit:
You can find some impressive hardware setup in the various kismet's discord channels. Most notably #3d-printing-design
That's what I tried. That's what the pwnagotchi project must use.
By the way, I forgot that I use a rpi0 with no (built-in) wifi, so this is not relevant for me
![Wink ;-)](./images/smilies/icon_wink.gif)
Edit:
You can find some impressive hardware setup in the various kismet's discord channels. Most notably #3d-printing-design
Return to “Net Hugging Hardware and Software”
Who is online
Users browsing this forum: Google [Bot] and 13 guests