Page 1 of 1

Hak5 WiFi Coconut

Posted: Thu Aug 18, 2022 9:45 pm
by larsnl
Looks like a nice compact device for a semi-portable car-setup, combined with a Raspberry Pi or notebook with GPS
Only internal antenna(s), I wonder how it will perform in the car.
https://shop.hak5.org/products/wifi-coconut

Currently using a Kali Notebook with latest Kismet connected to an GPS antenna/USB-Hub/4 USB Alfa WiFi adapters.
Adapters connected to 4 flat panel directional antennas positioned in the cat behind the rear side windscreens, stationcar 2 left 2 right
3 adapters set to fixed channels 1,6,11 nr 4 hopping 5 Ghz

Re: Hak5 WiFi Coconut

Posted: Sat Aug 20, 2022 12:31 am
by power64
The coconut appears to have an IPEX (IPX) connector where all the radios come together into a top patch antenna near the fan, so in theory, one could remove that and add an IPX to female SMA bulkhead with an external antenna and be off to the races. It's unknown if there are additional amplifiers in-line with each radio, as a 1:14 splitter will reduce the signal strength by around 12dB in losses with one input antenna. There are also 14 smaller Rf test ports/switches for each radio, however these RF connectors do not appear to be IPX and maybe Murata.

Be carefully pulling up the one main antenna off the board, as I accidentally ripped the IPX female connector off the board while attempting to gently pull up the IPX male connector out of the female soldered socket with equal pressure from both sides. An old salty dog friend said it might have been a cold solder joint, as the connector should have popped off the connector before ripping the solder joint, so be careful if you go this method. Some flux and hot air might be able to re-attach it.

Now if only dragorn or mkershaw come out with a Win x64 Coconut binary that support a generic GPS/NMEA GPS input, then anyone could Wardrive in style with Windows and 14 radios. I bet it would be the fastest setup for a multi-radio war-driving rig ever.... ;)

Re: Hak5 WiFi Coconut

Posted: Wed Aug 02, 2023 10:06 am
by computerb0y
The coconut appears to have an IPEX (IPX) connector where all the radios come together into a top patch antenna near the fan, so in theory, one could remove that and add an IPX to female SMA bulkhead with an external antenna and be off to the races. It's unknown if there are additional amplifiers in-line with each radio, as a 1:14 splitter will reduce the signal strength by around 12dB in losses with one input antenna. There are also 14 smaller Rf test ports/switches for each radio, however these RF connectors do not appear to be IPX and maybe Murata.

Be carefully pulling up the one main antenna off the board, as I accidentally ripped the IPX female connector off the board while attempting to gently pull up the IPX male connector out of the female soldered socket with equal pressure from both sides. An old salty dog friend said it might have been a cold solder joint, as the connector should have popped off the connector before ripping the solder joint, so be careful if you go this method. Some flux and hot air might be able to re-attach it.

Now if only dragorn or mkershaw come out with a Win x64 Coconut binary that support a generic GPS/NMEA GPS input, then anyone could Wardrive in style with Windows and 14 radios. I bet it would be the fastest setup for a multi-radio war-driving rig ever.... ;)
Hopefully by now we should have some performance reports... anyone?

Re: Hak5 WiFi Coconut

Posted: Wed Nov 08, 2023 12:01 am
by pretenda
Yah I'm super curious on this also.

How can I get Vistumbler to get more APs with Hak5 technology? Is it just as easy as plug it in and drive away?